“Water heating” system
Instructions insulation, by installing a warm water floor:
• We clean the floor surface, eliminate various defects, such as chips and cracks.
• We distribute the insulation around the entire perimeter of the surface.
• In order to avoid deformation of the floor during thermal expansion, we attach a damping tape along the walls.
• Next, install the reinforcing mesh on the floor, excluding those places where heating is not needed, lay out the pipes, observing the distance from the pipes to the wall of 10 centimeters.
• Also, to prevent pipe deformation during installation of the pipeline system, it is necessary to leave some free space.
• The next step is to connect the pipeline system to the heating system by using inlet and outlet manifolds. We fix the connection points with a winding or a coupling.
• Next, we check the system for leaks by maximizing its water flow capacity.
• If there are no leaks, we form a cement screed, first black after self-leveling.
• The absorbent layer is placed between the screed and the final coating.
• Finishing coat.
Features of the insulation of the bath floor
Expanded clay
• For the waterproofing layer, a layer of polyethylene is used in the form of a film, spreading it on a rough screed with access to the wall.
• Beacons are placed on the final level.
• Fill in the insulation.
• On top of the insulation, cover with a layer of cement.
• If it is necessary to lay reinforced mesh, proceed.
• A screed 3-4 centimeters thick is poured onto the insulation in cement.
• The drying time of concrete is on average 27-30 days, polymer up to 6-7 days.
• If any air bubbles remain, they can be etched out with a special roller.
Perlite
• First, make sure that the room is hermetically sealed, because the material is blown up by the wind.
• After “preparing” the composition we need by soaking the insulation with water, in a two-to-one ratio, we wait for complete shrinkage by rotating it beforehand.
• It is necessary to introduce this solution into the cement in parts until the ratio to the total is reached.
• After the desired mixture is obtained, another part of perlite and parts of water are added to it.
• We mix everything thoroughly, when the water is on the surface, the solution can be considered ready.
• The thickness of the layer that is laid out on the concrete surface should not exceed 10 centimeters, after which it hardens for six days.
Attention! To obtain an effective perlite paste, strictly observe the necessary proportions, do not try to add water if the solution seems too dry and crumbly to you.
Thermal insulation of the dressing room
• The dressing room, unlike a bathhouse, does not suffer from excessive moisture and excess temperatures, therefore, a waterproofing layer is not needed for floor insulation.
• The insulation is placed between the black and the finished floor.
• As for the steam room and the washing room, the waterproofing layer is 100% necessary.
• It is also possible, without disassembling the finishing flooring of the steam room, to install insulation material on top of it, which will maximize the effect of thermal insulation.
• With this insulation, the floor rises to an average of 15 centimeters, resulting in faster heating. 1xBet Anniversary Bonus offers signed-up clients a free bet. The 1xbet promo code free bet enter this code in the registration form to get a 100% welcome bonus up to 130$. New customers will get a €130 exclusive bonus (International users) when registering using the 1Xbet promo code listed above. The 1xBet bonus code you can claim will depend on where you live.
Instructions insulation, by installing a warm water floor:
• We clean the floor surface, eliminate various defects, such as chips and cracks.
• We distribute the insulation around the entire perimeter of the surface.
• In order to avoid deformation of the floor during thermal expansion, we attach a damping tape along the walls.
• Next, install the reinforcing mesh on the floor, excluding those places where heating is not needed, lay out the pipes, observing the distance from the pipes to the wall of 10 centimeters.
• Also, to prevent pipe deformation during installation of the pipeline system, it is necessary to leave some free space.
• The next step is to connect the pipeline system to the heating system by using inlet and outlet manifolds. We fix the connection points with a winding or a coupling.
• Next, we check the system for leaks by maximizing its water flow capacity.
• If there are no leaks, we form a cement screed, first black after self-leveling.
• The absorbent layer is placed between the screed and the final coating.
• Finishing coat.
Features of the insulation of the bath floor
Expanded clay
• For the waterproofing layer, a layer of polyethylene is used in the form of a film, spreading it on a rough screed with access to the wall.
• Beacons are placed on the final level.
• Fill in the insulation.
• On top of the insulation, cover with a layer of cement.
• If it is necessary to lay reinforced mesh, proceed.
• A screed 3-4 centimeters thick is poured onto the insulation in cement.
• The drying time of concrete is on average 27-30 days, polymer up to 6-7 days.
• If any air bubbles remain, they can be etched out with a special roller.
Perlite
• First, make sure that the room is hermetically sealed, because the material is blown up by the wind.
• After “preparing” the composition we need by soaking the insulation with water, in a two-to-one ratio, we wait for complete shrinkage by rotating it beforehand.
• It is necessary to introduce this solution into the cement in parts until the ratio to the total is reached.
• After the desired mixture is obtained, another part of perlite and parts of water are added to it.
• We mix everything thoroughly, when the water is on the surface, the solution can be considered ready.
• The thickness of the layer that is laid out on the concrete surface should not exceed 10 centimeters, after which it hardens for six days.
Attention! To obtain an effective perlite paste, strictly observe the necessary proportions, do not try to add water if the solution seems too dry and crumbly to you.
Thermal insulation of the dressing room
• The dressing room, unlike a bathhouse, does not suffer from excessive moisture and excess temperatures, therefore, a waterproofing layer is not needed for floor insulation.
• The insulation is placed between the black and the finished floor.
• As for the steam room and the washing room, the waterproofing layer is 100% necessary.
• It is also possible, without disassembling the finishing flooring of the steam room, to install insulation material on top of it, which will maximize the effect of thermal insulation.
• With this insulation, the floor rises to an average of 15 centimeters, resulting in faster heating. 1xBet Anniversary Bonus offers signed-up clients a free bet. The 1xbet promo code free bet enter this code in the registration form to get a 100% welcome bonus up to 130$. New customers will get a €130 exclusive bonus (International users) when registering using the 1Xbet promo code listed above. The 1xBet bonus code you can claim will depend on where you live.
